Wilton 2232AC Operations Instructions

Operating Instructions and Parts Manual 20-inch Variable Speed Drill Presses Models: J-2221VS, J-2223VS, J-2232AC, J-2234AC WALTER MEIER (Manufa

10 Operating Controls Manual Speed Control (Models J-2221VS and J-2223VS) Refer to Figure 4. Spindle Selector Switch A three-position selector switch

11 RPM Display The spindle speed display shows the spindle RPM selected by the speed control knob. Spindle Speed Knob The SPINDLE SPEED knob is used

12 12. Secure small head cover to head cover using pan screws. 13. Set the drill press circuit breaker ON. 14. Operate the drill press to verify cor

13 Figure 7 Adjustments Table Adjustment Refer to Figure 8. The table can be raised or lowered to accommodate the height of the workpiece. To raise

14 Drilling Recommendations Speeds for Drilling The speed of a drill is usually measured in terms of the rate at which the outer periphery of the too

15 Optional Equipment Coolant System Installation 1. Remove the large reservoir cover plate from the machine base. Tap 1/4-20 threads in the 4 pilot

16 Troubleshooting Trouble Probable Cause Remedy Spindle does not turn. Motor overload protector tripped. Press motor overload reset button. Circui

17 Drill Head – Manual Speed Control (J-2221VS and J-2223VS) 11B11A87252423222021191716151880C80B3029282780A80263233341110912131439403941353749464

18 Parts List: Drill Head – Manual Speed Control (J-2221VS and J-2223VS) Index No. Part No. Description Size Qty 7 ... 5510077 ...

19 Index No. Part No. Description Size Qty 61 ... 5510131 ... Thrust Bearing ...

2Warranty and Service JET, Wilton and Powermatic warrants every product they sell against manufacturers’ defects. If one of our tools needs service o

20 Drill Head – Inverter Speed Control (J-2232AC and J-2234AC) 7473727779818082838686-19087887576858484-12987654321201514131012161822232626-127282

21 Parts List: Drill Head – Inverter Speed Control (J-2232AC and J-2234AC) Index No. Part No. Description Size Qty 1 ... J-5517332

22 Index No. Part No. Description Size Qty 56-1 ... 5510197 ... Speed Proximity Switch ...

23 Spindle Components (All Models) Parts List: Spindle Components (All Models) Index No. Part No. Description Size Qty 1 ... J-

24 Index No. Part No. Description Size Qty 26 ... 5510261 ... Socket Head Screw ...

25 Table and Base (All Models) 20A1918-11618-318-21837-1341237212332A31172212515053424143344977-18946474815393610131411302926A2524119-1638535-135

26 Parts List: Table and Base (All Models) Index No. Part No. Description Size Qty 1 ... J-5510288 ... Base...

27 Index No. Part No. Description Size Qty 36 ... J-5510321 ... Table Raise Crank ...

28 Wiring Diagram – Models J-2221VS and J-2223VS

29 Wiring Diagram – Models J-2232AC and J-2234AC

3Table of Contents Warranty and Service ...

30 NOTES

31

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jetto

4 Warning - Misuse of this machine can cause serious injury. - For safety, machine must be set up, used and serviced properly. - Read, understand

514. Remove adjusting keys and wrenches before turning machine on. 15. Use the right tool. Don’t force a tool or attachment to do a job for which it

6Safety Instructions for Drill Presses 1. All work shall be secured using either clamps or a vise to the drill press table. It is unsafe to use your

7General Specifications The JET 20-inch Variable Speed Drill presses Models J-2221VS, J-2223VS, J-2232AC and J-2234AC are available in manual speed c

8The JET Model J-2221VS and J-2223VS drill presses feature manual speed control. Models J-2232AC and J-2234AC have inverter speed control. This manua

9 Raising the Drill Head and Table The drill press is shipped with the table and drill head supported by wooden blocks near the bottom of the column.