Wilton 7015 Owner's Manual

Owner's Manual 8-in x 13-in Horizontal Cut-Off Bandsaw Model: 7015 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-7015Ph.: 8

10Blade Selection The cut-off saw is delivered with a saw blade that is adequate for a variety of cut-off jobs on a variety of common materials. A 10-

11Evaluating Cutting Efficiency Is the blade cutting efficiently? The best way to determine this is to observe the chips formed by the cutting blade.

12Starting the Saw Important: The efficient operation of the cut-off saw is dependent upon the condition of the saw blade. If the performance of the s

13Coolant Flow and Nozzle Position The coolant pump must be submerged before operating to prevent damage to the pump. Adjust the coolant flow shut-of

AdjustmentsBlade Tracking Adjustment Refer to Figures 13 and 14. Blade tracking has been set and tested at the factory. Adjustment is rarely required

15Repeat the insertion of the paper between the wheel shoulder and the blade until the paper is cut in two pieces. Note: You may have to repeat the c

16Blade Guide Bearing Adjustment Referring to Figure 16: Guide bearings and guide inserts are located on either side of the saw blade and provide stab

17Verifying Adjustment Accuracy Refer also to Figure 18. Test cuts can be used to determine whether or not you have adjusted the blade accurately. Use

18MaintenanceFigure 21 Changing Blades Use leather gloves when changing the saw blade to protect your hands from cuts and scratches. Use protective e

Changing the Drive Belt Referring to Figures 22 and 23: Disconnect the cut-off saw from its electrical power source. 1. Set the arm at the full hor

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servic

Cleaning1. Clean off any preservative on machine surfaces. After cleaning: 2. Coat machined surfaces of the cutoff saw with a medium consistency mac

21TroubleshootingFault Probable Cause Suggested remedy Excessive blade breakage 1. Material loose in vise. 2. Incorrect speed or feed. 3. Teeth t

22TroubleshootingFault Probable Cause Suggested remedy Bad cuts (rough) 1. Blade speed too high for feed pressure. 2. Blade is too coarse. 1. Red

23PartsSaw Stand and Bed Index No. Part No. Description Size Qty 1-1 ...TS-1499141 ...Hex Cap Screw ...

24Saw Stand and Bed Index No. Part No. Description Size Qty 31 ...TS-1490031 ...Hex Cap Screw ...

25Saw Stand and Bed – Parts Breakdown

26Saw Head Index No. Part No. Description Size Qty 200 ...7015-200...Blade Guard...

27Saw Head Index No. Part No. Description Size Qty 314-1 ...7015-314-1...Connector...

28Saw Head Index No. Part No. Description Size Qty 354-8 ...TS-1503071 ...Socket Head Cap Screw...

29Saw Head – Parts Breakdown

3Table of ContentsWarranty and Service...

30Electric Assembly – Parts and Breakdown Index No. Part No. Description Size Qty 5-1 ...7015-5-1...Fuse Base...

31Wiring Diagram

32Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST), Monday through Frida

4Warnings1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted o

521. Keep visitors a safe distance from the work area. Keep children away.22. Make your workshop child proof with padlocks, master switches or by re

6Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor in

7Machine Features Figures 1 and 2 depict the main features of the Model 7015 Horizontal Cut-Off Bandsaw. The machine consists of a machine base onto w

8The mechanism also has adjustment screws that enable the saw blade to “track” evenly on the blade wheels. The adjustment screws change the angle of t

92. Place a warning placard or tag on the service panel to prevent accidental electrical shock. 3. When installing the motor power cord into a recep