Wilton 4126AC Operations Instructions

This Manual is BookmarkedOperating Instructions — Parts ManualSquare Wheel Belt GrinderModels: 4103, 4106, and 4126ACPart No. 5507796Revision C2 09/04

10MaintenanceCleaningShutoff the machine before cleaning. Keep the exteriorof the machine clean and free of chips. Use a brush forcleaning. Periodic

11Replacement of Grinding BeltWARNING: DO NOT OPERATE THE MACHINE WITHTHE SIDE PANEL OPEN. DISCONNECT ELECTRI-CAL POWER TO THE MACHINE BEFORE PERFOR

12Wiring DiagramsModel 4103Model 4106Model 4126AC

13TroubleshootingProblem Probable Cause Suggested RemedyPoor Tracking 1. Improper belt splice. 1. Check belt for irregular seam or shape.2. Excess

14Exploded View - Square Wheel Belt Grinder45

15Parts List - Square Wheel Belt GrinderRef. PartNo. Number Description Qty.Ref. PartNo. Number Description Qty.1 5510944 Contact Wheel Assy, 10 x 2 S

16Ref. PartNo. Number Description Qty.1 5550874 Screw, Socket head 7Cap, 10-32NF x 3/82 5507817 inverter (1ph, 120V, 50/60Hz) 15507818 Inverter (3ph,

17AccessoriesBelt Grinder PedestalThe optional pedestal enables the Square Wheel BeltGrinder to be mounted in a free standing configurationrather than

18Exploded View - Vacuum ScoopA vacuum scoop connects the machine to the vacuum system. The mounting provisions for the scoop areshown in the explode

19Air Cushioned Dead Head AssemblyRefer to Figures 10 and 11. The air-cushioned deadhead is for use on very small radius grinding. Whenconnected to a

20Figure 13: Hub and Wheel Assembly41V-BeltCollarHub ShaftRef. PartNo. Number Description Qty.1 5054920 Hub and Wheel Assembly 1(Includes Hub Shaft, V

21Dia.(In.) Part Number Description1/2 5057871 Contact Wheel, 70 Duro5/8 5057881 Contact Wheel, 70 Duro3/4 5057891 Contact Wheel, 70 Duro1 5057901 Con

22Figure 16: Assembly of Grinding Machine and PedestalABCDMotor SideHoles20 inchesapartBelt Guard HolesApproximately1/2-inch fromcornersInstall two 1-

23InstallationTransport the shipping container to the installation site.Unpack the dust collection system and check fordamage. Contact the carrier if

24DisassemblyDisassembly of the dust collection system is re-quired only to replace the motor or the fan compo-nents. The motor switch, if failed, ca

2515 14222116242892325262019271213181711105 6784123Exploded View – Model 5511885 Dust Collection SystemFRONT VIEWREAR VIEW641232728

26Parts List – Model 5511885 Dust Collection SystemRef. PartNo. Number Description Qty1 5514731 Base 12 5514732 Drawer, Chip3 5514733 Seal, Tape (5-fe

27

WMH TOOL GROUP2420 Vantage DriveElgin, Illinois 60123Phone: 800-274-6848

3Table of ContentsCover Page ...

4General SpecificationsThe Wilton Square Wheel Belt Grinder,Models 4103, 4106 and 4126AC, aredesigned for grinding, deburring,chamfering, and internal

5- Misuse of this machine can cause serious injury.- For safety, machine must be set up, used andserviced properly.- Read, understand and follow instr

6 A B C D17. Keep hands in sight and clear of all mov

7IntroductionThis manual includes operating and maintenance instructions for the Wilton Model 4103, 4106 and 4126ACSquare Wheel Belt Grinder. The manu

8Vacuum ConnectionNOTE: A variety of vacuum system optionsare available. (Refer to Accessories section.)The grinder uses a front mounted vacuum syste

9Typical Uses for the Square Wheel Belt GrinderFlat or angularstock — Platensetting is the perfectangle for high speed,precision, flat andlevel grindi