Wilton 1230 Operations Instructions

Part No. 9078241Revision ARadial Arm Drill PressModel 1230Operating instructions and parts manual

10pushed inward -- on pivots which are in the feed leverhub. When the feed levers are pushed toward thedrill head, the power feed mechanism is diseng

11Spindle direction and power feedThe spindle can be driven clockwise or counter-clockwise. The direction of rotation is controlled bythe control lev

12Resetting the STOP switch1. Turn the switch in the direction of the arrow on thered button -- clockwise. The switch is reset and theother spindle

13release it. Rather, the lever stays in the position inwhich you put it when you are controlling the spindle.There is no need to hold it in position

141. Lift the drill press from its shipping skid accordingto the diagram, below.2. Secure the drill press to the floorThe drill press MUST be anchore

15to the ON position.6. Observe the direction of rotation of thecoolant pump. You can see the pump shaft rotateon top of the pump at the rear of the

16Figure 6: Wiring diagram

17Replacement PartsThis section provides exploded view illustrations that show the replacement parts for the Wilton 4 foot arm,Model 1230 Radial Dril

18Exploded View - Column and Base

19Parts List - Column and Base1 5232911 Base2 5232921 Bolt3 5232931 Needle bearing4 5232941 Internal column5 5232951 Bolt6 5232961 Top bearing cover7

201 5235751 Bolt2 5235761 Washer3 5235771 Bushing4 5235781 Round bar5 5235791 Plain washer6 5235811 Nut7 5235821 Nut8 5235831 Bolt9 5235841 Chain fram

211 5233311 Lamp cover2 5233321 Screw3 5233331 Lamp4 5233341 Lamp seat5 5233351 Arm rack6 5233361 Bolt7 5233371 Arm8 5233381 Locking shaft9 5233391 Oi

22Exploded View - Arm (Rear)

23Parts List - Arm (Rear)50 5236551 Bolt51 5236561 Gear52 5236571 Block53 5236581 Block54 5236591 Bolt55 5236611 Rack shaft56 5236621 Rack57 5236631 B

24Parts List - Riser MechanismRef no. Wilton part no. Description1 5232451 Motor2 5232461 Key3 5232471 Screw4 5232481 Adapter5 5232491 Plastic sh

25Exploded View - Head

26Parts List - Head1 5233551 Hand wheel lock nut2 5233561 Hand wheel3 5233571 Plastic knob4 5233581 Feed handle5 5233591 Pin6 5233611 Clutch housing7

27109 5234751 Oil level gage110 5234761 Gear box111 5234771 Gear112 5234781 Spring113 5234791 Steel ball114 5234811 Sleeve115 5234821 Worm gear sleeve

28Parts List - Rear of Head1 5235411 Bolt2 5235421 Eccentric shaft3 5235431 Gear box4 5235441 Bolt5 5235451 Adjustable collar6 5235461 Adjustable coll

Parts list - Flood Coolant SystemRef no. Wilton part no. DescriptionRef no. Wilton part no. Description1 5232251 Fixed blade2 5232261 Cross screw3

3Table of ContentsCover Page ...

30Notes:

Wilton Corporation300 South Hicks RoadPalatine, IL 60067TEL: 1-888-594-5866FAX: 1-800-626-9676

4Column diameter 11 13/16 in. (295mm)Column to spindle center distance, max. 46 in. (1150mm)Column to spindle center distance, min. 13 3/8 in. (334mm)

5-Always shut off the machine when not in use.When servicing machine:-Always unplug machine from electrical power whileservicing.-Always follow instru

6240 volt lines 120 volt lines0-50 feet No. 14 No. 1450-100 feet No. 14 No. 12Over 100 feet No. 12 No. 8Conductor lengthAWG (American wire gauge) numb

7Operating InstructionsClamping workpieces to the machineBoth the box table and the base surface areslotted to accept a suitably sized T-slot clamp.Be

8Inserting toolingThe Model 1230 uses a #4 Morse taper in thespindle to secure tooling. Any drill, milling cutter, ortool holder with a #4MT can be i

9on LOW or HI speed. There is a chart on the front ofthe drill head which shows you the spindle speedsavailable and the gear change lever and motor s